CUSTOM PLAY ARTS KAI – Barret Wallace :FINAL FANTASY VII REMAKE with BACK PART

ภาษาไทยกดที่นี่

CUSTOM PLAY ARTS KAI – Barret Wallace :FINAL FANTASY VII REMAKE

Form Review PLAY ARTS KAI – Barret Wallace :FINAL FANTASY VII REMAKE. I said I got problem with Right Shoulder Joint that attach to the body was glued. I try to pry it but It’s still stuck. So I find the way to remove the jacket for easier work with the joint. The Joint was glued very very very tight. I twisted and pulled until It broken! In addition, I must remove leavings joint. The result is the joint and hole were sloppy. Right here I fixed the joint’s hole by used “Foam Rubber Sheet”. Cut it into a rectangle. Size is around pin of joint.(see image-1 A.) Roll it to tube form then put it in joint’s hole and glue between Foam Rubber Sheet and hole’s surface.

And The Broken Joint, Yes It’s broken so I will find replacement joint to replace it. And Play Arts KAI General Zod is a sacrificer (Sorry T-T). I got a black joint from him. When I attached everything back except Barret’s Jacket. I got the idea I should create a back part for Barret. Then I was making it at that time. I make out, measured and cut Foam Rubber Sheet for test.(see image-1 B.)

Finally, I think it’s totally OK. It can use and cover shoulder hollow. lol

Thank you @Beamnoi for support the figure.

Thanks and Let’s see the photos

You can support me and my work at

Donate  or  Donate


ปรับแต่ง PLAY ARTS KAI – Barret Wallace :FINAL FANTASY VII REMAKE

จาก รีวิว PLAY ARTS KAI – Barret Wallace :FINAL FANTASY VII REMAKE ที่แจ้งปัญหาไปว่า ข้อต่อแขนตรงส่วนที่เสียบกับลำตัวโดนกาวมาตั้งแต่แรก เลยพยายามงัดดู แต่ไม่ออก ก็เลยต้องแกะเสื้อแจ็คเก็ตออก เพื่อง่ายต่อการงัด คือกาวมาแน่นมาก พยายามบิดและดึงข้อต่อออก บิดจนข้อต่อหัก! แถมยังต้องมางัดส่วนที่ติดด้านในอีก ผลคือ ชิ้นที่เหลือเละ รวมถึงรูที่เสียบด้วย ตรงนี้ก็พยายามซ่อมโดยใช้ โฟมยางสีดำ ตัดเป็นสีเหลี่ยมผืนผ้า ขนาดพอๆปลายข้อต่อ(ดู image-1 A.) ขดเป็นทรงกระบอก ,ใส่รู และกาวรอบๆพื้นผิวที่ติดกับผิวโมเดล

มาที่ข้อต่อ มันหักนิ เลยต้องหาข้อต่อมาเปลี่ยนแทน ซึ่งที่หาได้ก็เป็นสีดำ และผู้เสียสละคือ Play Arts KAI General ZOD นี่เอง (ขอโทษน้าา T-T) พอเสียบทุกอย่างกลับเข้าที่ยกเว้นเสื้อแจ็คเก็ต ก็เกิดไอเดียอยากทำชิ้นส่วนหลังขึ้นมา ก็จัดเลยจ้า ก็วัดๆกะๆเอา และก็เอาโฟมยางนั้นแหละมาตัดๆดู(ดู image-1 B.)

สรุป ผลที่ออกมา..ก็ รู้สึกโอเคนะ แก้ขัดได้ ปกปิดไหล่โหว่งๆได้ ฮ่าๆ

ขอขอบคุณ @Beamnoi ที่สนับสนุนฟิกเกอร์สำหรับรีวิวนะครับ
ขอบคุณครับผม + ดูรูปกัน

คุณสามารถเป็นแรงใจ และสนับสนุนผลงานของผมได้ที่

Donate  หรือ  Donate

You can support me and my work at

Donate  or  Donate

Similar Posts:

Facebook Comments

  • Share post

Leave a Reply

Your email address will not be published. Required fields are marked *